How To Fix Underwire Poking Out Of Bra

Download Article

Moleskin Patch

Fabric Patch

Sewing

Exercise you have a bra with a protruding underwire? Don't throw the bra away! A protruding underwire is fixable with a few simple items. Decide on which method works best for you based on what you have on hand.

one

Buy moleskin padding. This padding is found in the foot section at drugstores. Most moleskin comes in peel colors, so you may have a harder time matching it to your bra. Information technology's used to pad corns and calluses, but today, you'll utilise it to ready your bra. A modest package will do, as y'all don't demand very much.^[1]
2

Cut a strip. Only similar with the fabric, you lot will cutting a strip of moleskin large plenty to patch the pigsty. Yous may want it big enough to go over the edge of the bra for more than stability. Also, attempt to round off the corners and then the cloth won't poke you.^[2]

Ad
3

Poke the wire dorsum in. Find the place the wire is sticking out. Push it all the manner back in, and so you lot can't see the wire anymore. You may want to cover it up a scrap with the cloth from the bra. Only stretch it out a bit and use the ane side of the rip to encompass it up.^[three]
4
Encompass upward the pigsty. Peel the paper backing off the moleskin. Put the strip mucilaginous-side down over the hole, and bend information technology over the border of the bra if yous need to. Smoothen it out with your fingers, and the patch is done.^[4]
- Make sure you spend some extra time smoothing with the moleskin. The moleskin needs the rut from your skin to really adhere to the fabric.

Advertizing

1

Cut a piece of thick canvas or fabric. You lot'll use this slice of material to patch the pigsty, then it needs to exist large enough to cover it. You may want to bend information technology over the edge of the bra for extra security, so brand sure it is large enough to practise so.^[5] Yous may also desire to cull a slice of material that's similar in color to your bra. That style, that patch will blend in improve.
two
Cut out a piece of fabric adhesive. The adhesive strip should be about the aforementioned size equally the cloth strip. You can hold the fabric strip up to the canvas to measure information technology. As you concord it, cut around the strip.^[6]
- At the fabric shop, y'all can observe packages of ii-sided fabric adhesive sheets. Some of these are iron-on, but for this project, using one that doesn't crave ironing is better, every bit it's non a good idea to fe some bras.
iii
Back the material strip. Peel off one side of the paper backing on the agglutinative strip. That volition reveal a viscous strip of adhesive. Carefully adhere the strip to the cloth, trying to go information technology shine. The other side of the strip should still be backed with paper.^[vii]
- Once y'all've got it backed, trim upwards the edges. Also, round off the corners so that they don't poke you afterward.
4

Push the wire back in the bra. Hold up your bra where the wire is sticking out. Push the wire all the mode back in so that all you meet is a pigsty. Try to cover the end of the wire up with a flake of fabric from the bra past moving it around until it's in a skillful place.^[8]
five

Put the fabric strip on. Remove the paper backing from the other side of the adhesive. Place the strip sticky-side downwards over the hole. Y'all tin bend the strip over the edge of the bra for more than security. Shine it down, making sure it is stuck well, and you're washed.^[9]

one
Thread a needle. Offset out past threading a needle. Y'all'll desire a fairly sturdy needle, but y'all don't want one so thick that you'll have a difficult time pulling it through. Use a thick thread or double thread information technology for extra forcefulness. Knot the end of the thread so information technology won't pull through the fabric.^[10]
- To double thread a needle, smoothen two pieces of thread together. Cut the cease so the pieces are even. Button both pieces of thread through the eye of the needle at the same time. Go out at least 4 or 5 inches of tail then that the needle doesn't come up unthreaded.
- An easy mode to knot the thread is to find the terminate of the thread. Hold information technology up against the needle and then that the needle is facing towards the length of the thread, not the end. While holding the end of the thread against the needle near the eye, wrap the thread around the sharp terminate of the needle three times. Put your fingers over where you wrapped the thread, and pull the needle through. Still holding the loops with your fingers, let the length of the thread go through the loops until it knots at the end. Cut off any extra thread.
2

Button the wire dorsum in. Find the place the wire is sticking out. Push it all the way back in. Gather the the ii edges of the fabric that surround the hole by pulling up a chip on each edge and belongings them together so that the edges come across, sticking upwardly towards yous.^[11]
3
Sew the edges together. With the edges together, beginning sewing on one stop of the pigsty. Pull the needle through both edges. Loop the thread over the edges, and start on the same side over again. Push button the needle through again. Keep making this stitch (a whip stitch) until you achieve the other edge of the hole. Knot the thread off.^[12]
- Make sure to make your stitches shut together to keep the wire from escaping. Also, information technology'due south probably a adept idea to run up a little chip farther than you retrieve you should on each side to assist reinforce information technology.^[13]
4

Reinforce the stitching. Use a bit of boom shine or fabric glue to reinforce what you've done. But paint or spread a scrap of the substance over the stitching. Make sure to piece of work it into the stitches if you can. Let the substance dry, and y'all're done.^[14] You tin can also use superglue for this step.^[fifteen]

Add together New Question

Question

What if the wire is broken?

Open up the cease with a seam ripper and pull out the broken wire and supersede information technology with a new one. (Y'all can fine them at JoAnn's Fabrics, Hobby Foyer, Michael'south or Walmart). Once you slide a new ane in, just secure the open end past stitching it support.
Question

How can you fix it if the wire broke and was thrown away?

Adara Horn

Community Answer

You can buy underwires from several stores online.
Question

Where can I purchase the correct size of rings to set up straps?

Jo-Ann Fabrics if you have one in your area. There'due south too Hobby Lobby, Michael's, and Walmart.

Enquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

While these fixes will exist by and large permanent, it may exist a expert thought to hand wash the bra from now on. The sewing method volition likely hold upward to washing improve than the other methods.

Thanks for submitting a tip for review!

About This Commodity

Article Summary 10

If you have an underwire bra that you'd like to repair, cut a strip of thick canvas or material that's just large enough to cover the hole. Adjacent, cut a strip of double-sided fabric agglutinative that's almost the aforementioned size every bit the patch you just cut. Skin off ane side of the paper backing and carefully stick the adhesive to the fabric. Once you've done that, push the underwire dorsum into the bra, then skin off the remaining newspaper from the agglutinative and press the viscid side of the patch over the hole. If you'd like to know how to sew together the hole closed, read on!

Did this summary help y'all?

Cheers to all authors for creating a page that has been read 198,108 times.

Did this commodity aid you?